We have the video, but here is not allowed to show, pls sent us message, we will sent you the video link

 

What is HUD:

 

1.    Parameter value: show the value with the units of kilometers, miles and engine speed.

2.    OBDII port: connect the car and HUD.

3.    Fuel icon: flash when the fuel is not enough to drive 100km.

4.    Engine failure: flash when vehicle’s engine has problems.

5.    Engine speed: show the state of engine speed.

6.    Engine speed icon: indicate the parameter value of engine with units of 1000r. It will flash when engine speed is alarming.

7.    Speed alarm: flash when speed exceeds the preset values.

8.    Rest tips: flash when drive continuously for more than 4 hours with HUD starting.

9.    Sound switch: light when voice alarm is opened.

10.  Fuel consumption icon: show fuel consumption is calculating.

11.  Fuel parameter value: show the consumption of fuel in recent driving.

12.  Dial button: multi-function switch, you can dial to left or right, you can enter into setting mode by long press. And also has the ability to decrease or increase fuel.

13.  Fuel consumption per hour: show oil mass consumption per hour in driving.

14.  Light sensor: sense the external light intensity and adjust the HUD’s brightness to adapt to environment automatically.

15.  Fuel consumption per 100km: show the fuel consumption per 100km in driving.

16.  Voltage, throttle valve, water temperature, ignition advance angle and acceleration per 100km: voltage shows the vehicle’s voltage; throttle valve shows the size of itself; water temperature shows the temperature of vehicle cooling fluid; ignition advance angle shows the angle of twist in firing, it’s also a mark of engine’s efficiency. Acceleration per 100km shows performance of the vehicle’s acceleration per 100km.

17.  Seconds: show the unit of acceleration per 100km.

18.  Parameter value: show parameter value of Voltage, throttle valve, water temperature, ignition advance angle and acceleration per 100km.

19.  Mileage: light when the fuel only sustains 100km.

20. Reel per minute: show the unit of engine speed if you multiply the parameter value with 10.

21.  Kilometer per hour: show the unit of speed.

22.  Mile per hour: show the unit of speed.

 

Main Technical Indicators

1.    Service conditions:

Environment temperature: -40⁰C—+80⁰C

Barometric press: 86—106 KPa

Relative humidity: 10%—95%

Environment voice: <=60 dB(A)

2.    Alarm of sound level:> =30dB(A)

3.    Work voltage: 9V~16Vdc(12Vdc/400mA)

4.    Size of product: 14x85x147 (mm)

5.    Weight of product: 320g

 

Preparation before installation and use

1.    Know the type of your vehicle. When purchasing HUD, you need to choose the type of vehicle that meets the OBDII standards for normal use. Open the engine hood and find the paster below it (see the picture below), if it has words like OBDII CERTIFIED, then it can be installed. Check if there is a test diagnostic communication link (TDCL) under the steering wheel. (Most of the vehicles after 2006 in China have been equipped with a TDCL)

 

2.    Find out the diagnostic link (see the picture below) of vehicle 16 pin and connect it well with OBDII connecting line. As different types of vehicles have different positions for diagnostic link and some are relatively narrow, patch cord can be purchased.

3.  Put the give-away non-slip mat at the flat place in front of the navigation bridge, then you can place the host machine of HUD on it and adjust its location at any time.

4.  The reflecting film should be pasted right above the H101 host machine and it should be able to reflect the mainframe screen.

Methods of pasting the film:

A . equably water the place that the film will be pasted on ;

B . rip off the covering layer of the film , and water both sides of it , and paste it to the right place.

C.  After you have adjusted the location well, you can use a scratch board or something else flat to slick the film and squeeze the water inside out until there is no bubble or water in it.

D.  A few minutes later, the moisture inside the film totally evaporates , then you can finish this by wiping away the water and dust around .

 

Accessories of product

Host machine of HUD  .................................................................... ×1

Reflecting film................................................................................. ×1

OBD connecting line........................................................................ ×1

instruction book............................................................................... ×1

non-slip mat..................................................................................... ×1